UVC LED
- 光学传感器/Optical Sensor
- 颜色传感器/Color Sensor
- 接近传感器/Proximity Sensor
- 紫外线指数传感器/UV Sensor
- 环境光传感器/Ambient Light Sensor
- 汽车光学传感器/Automotive Optical Sensor
- 心率血氧传感器/Heart Rate/Blood Oxygen Sensor
- 可见光LED/Visible LED
- 光耦/Photo Coupler, IGBT, SSR
- IGBT光耦/IGBT Gate Driver
- 高速光耦/High Speed Photocoupler
- 光耦晶体管/Phototransistor Output
- 可控硅光耦/Phototriac Output
- 达林顿光耦/Photodarlington Output
- 施密特触发器/Schmitt Trigger
- LED闪光灯/Flash LED
- 汽车LED/Automotive LED
- 紫外线LED/UV LED
- 红外线发射管/Infrared LED
- 红外线接收管/IR Detector,Silicon
- 光电开关/Photointerrupter
- 接收头/Infrared Receiver Module
- 光纤端子/Optic Fiber-Photo Link
新闻中心
- 2020-10-21新冠病毒,消毒方式该怎么选?
- 2020-10-09深紫外LED是怎么消毒的?
- 2020-09-14深紫外LED杀菌效果应该怎么评估
- 2020-09-07深紫外LED是什么和深紫外LED的作
- 2020-09-03深紫外LED的特点
联系我们
- 地址:中国广东省东莞市塘厦镇莲湖南路68号钜鸿电商产业园310
- 电话:0769-81775972
- 手机:13592705594
- 传真:0769-81775972
- 邮箱:lizhenhuafanglian@126.com
您现在的位置:网站首页 > UVC LED
FL280-PSM1F20M001
- 型号:FL280-PSM1F20M001
- 品牌:光宝
- 波长:270~280nm
- 封装:3737封装
- 产品描述: L280-PSM1F20M001是光宝UVC深紫外led的一款,光宝深紫外LED其波长为270~280nm,峰值波长为280nm,可用来消毒杀菌及医用光源,光宝280nm深紫外led采用氧化铝陶瓷支架,平面硅胶封装,防水性极好,杀菌率90%,适合用于吸尘器、除螨仪等产品,更多UVC LED欢迎联系光宝代理。
产品介绍
- 图纸单位: mm
- 封装:3737封装,外型尺寸:3.7×3.7×1.5 (L×W×H) [单位:mm]
- 封装材质:氧化铝陶瓷支架,平面硅胶
- 封装芯片数量:1 pcs
- 除非另有说明,公差为±0.10 mm
- Unit: mm
- LED Package: 3737 packaged, with size 3.7×3.7×1.5 (L×W×H) [Unit : mm]
- Bracket material:Alumina ceramic
- Chip inside:1 pcs
- Tolerances unless otherwise mentioned are ± 0.10 mm
- 这些数值由光谱分析仪和积分球测量系统测量。
- 公差如下:工作电压(Vf):±2%;光功率(P0):±10%;峰值波长(λp):±3.0 nm
- 虽然所有的LED都是由我们的设备进行测试,但根据测试设备的条件,某些值可能会略有不同。
- These values measured by Optical spectrum analyzer and integrating sphere measuring system.
- And tolerances are followings as below: Forward Voltage (Vf): ±2%, Radiant Flux (P0): ±10%, Peak Wavelength (λp): ±3.0 nm
- Although all LEDs are tested by our equipment, some values may vary slightly depending on the conditions of the test equipment.
8.使用条件 During Usage
- LED应避免直接接触有害物质,如硫磺,氯气,邻苯二甲酸盐等。
- 在操作和储存期间必须避免暴露于腐蚀性气体。
- 镀银金属部件不仅受到最终产品内部排放的腐蚀性气体的影响,还受到外部环 境渗透的气体的影响。
- 必须避免可能导致冷凝的突发环境温度变化或高湿度等极端环境。
- The LED should avoid direct contact with hazardous materials such as sulfur, chlorine, phthalate, etc.
- The metal parts on the LED can rust when exposed to corrosive gases. Therefore, exposure to corrosive gases must be avoided during operation and storage.
- The silver-plated metal parts also can be affected not only by the corrosive gases emitted inside of the end-products but by the gases penetrated from outside environment.
- Extreme environments such as sudden ambient temperature changes or high humidity that can cause condensation must be avoided.
9. 清洗注意事项 Cleaning
- 请勿使用刷子清洗或用有机溶剂(即丙酮,TCE等)进行清洗,否则可能会损坏LED的树脂。
- 在以下条件下,异丙醇(IPA)是推荐用于清洁LED的溶剂。
- 清洁条件:IPA,最高25℃。 ×60秒以内
- 不建议使用超声波清洁。
- 预测试应与实际清洁过程一起进行,以验证过程不会损坏LED。
- Do not use brushes for cleaning or organic solvents (i.e. Acetone, TCE, etc..) for washing as they may damage the resin of the LEDs.
- Isopropyl Alcohol(IPA) is the recommended solvent for cleaning the LEDs under the following conditions.
- Cleaning Condition: IPA, 25℃ max. × 60sec max.
- Ultrasonic cleaning is not recommended.
- Pretests should be conducted with the actual cleaning process to validate that the process will not damage the LEDs.